Diamond Drill
Blog · Drilling and geotechnics

Used Drill Rig Inspection Checklist Before You Buy

A used rig can be a good way to start or expand a drilling company. It can also be a very expensive mistake. A structured inspection, done in daylight with the rig running, protects the buyer. Use this checklist, and take a helper who knows the equipment or an independent inspector.

Before you go

  1. Ask for documents: proof of ownership, maintenance records, hours of use and past repairs.

  2. Ask which work the rig did. Hard rock and heavy use wear a rig faster.

  3. Find out if the model is still supported with parts and service.

The checklist

AreaWhat to checkRed flag
DocumentsOwnership, service history, hours of useNo records or hours that do not match the wear
StructureFrame, mast, pivots and pins, feed system, levellingCracks, repaired welds, bends, play in pins
EngineCold start, smoke, temperature, oil pressure, leaks, filtersHard start, heavy smoke, low pressure
HydraulicsPump, hoses, cylinders, oil condition, heat under loadLeaks, noise, oil that is dark or contaminated
Rotation headSmooth rotation across speeds, play, noiseAbnormal noise or play
Rod handlingClamps, breakout device, winch, extractorSlipping clamps, weak extraction
SPT hammerHammer or drop system works consistentlyVariable drop height or slow cycle
SafetyEmergency stops, guards, labels, clear controlsMissing guards or stops that do not work
Tracks and carrierWear, tension, leaks in the track drivesWorn tracks, leaking drives

Structure

  • Frame and mast: look for cracks, repaired welds, bends and corrosion, especially where the load is carried.

  • Pivots and pins: play and wear.

  • Feed system: chains, cables or cylinders in good condition.

  • Levelling and outriggers: straight, with no leaks or drift.

Engine and hydraulics

  • Starts easily with no excess smoke, with normal temperature and oil pressure.

  • No leaks, fluids in good condition, clean air and fuel filters.

  • Hydraulic pump holds pressure; hoses and cylinders have no leaks or damage; oil does not overheat under load.

Run it under load

Ask the seller to drill, if possible. A test under load shows faults that a static inspection hides. If drilling is not possible, operate every function through its full range: feed up and down, rotation at every speed, winch, clamps and levelling, and the SPT hammer if the rig has one.

Paperwork and support

  • Is the model still supported with parts and service?

  • Does it meet the safety requirements of your market?

  • What warranty does the seller offer, and in writing?

Compare with the alternatives

A used rig costs less at the start, but repairs and downtime add up. Compare it with a refurbished or new rig and with renting. See rent or buy: how to decide, how much it costs to start a drilling company and how to choose a geotechnical SPT rig.

For drilling companies: Diamond Drill lists used drill rigs as they become available and offers rig refurbishment to extend the life of your equipment.

Frequently asked questions

What should I check first on a used drill rig?

Start with the documents: ownership, maintenance records and hours of use. Then inspect the structure, engine and hydraulics, and finish with a test under load.

Should I buy a used drill rig without seeing it run?

It is risky. Faults in the hydraulics, rotation head or hammer often only show under load, so ask for a drilling test or operate every function through its full range.

How do I know if the hours of use are real?

Compare the hours with wear on pins, rod clamps, tracks and the rotation head, and with the maintenance records. A big mismatch is a red flag.

Is a refurbished rig better than a used one?

It can be, because worn parts are replaced and tested, and the supplier can give a warranty. Compare the total cost, including downtime, with a used and a new rig.

Need equipment for SPT?

Diamond Drill manufactures drilling rigs. Talk to our technical team and find the right solution for your work.

Need equipment for SPT?

Talk to our technical team.

Request a proposal →Our offices